ClearPath® Accessories Guide

Click on the appropriate series button below to view and purchase the accessories you need. To view all ClearPath accessories, Click Here.

Components DC Power SupplyPower CableController CableMSP SoftwareUSB Setup CableStep and Direction IndexerStep and Direction Indexer

Click Question Mark symbols in diagram for more details.

 


Controller Cables

Controller Cable

Controller Cable, 10 ft
Part Number: CPM-CABLE-CTRL-MU120
Connectors: 8-pin Molex Mini-fit to 8-pin Molex Mini-fit (one connector is overmolded)
Length: 3.05 m (10 ft)

This cable connects your digital control signals (from switches, buttons, PLCs, etc.) to your ClearPath motor. The overmolded Molex connector connects to the motor (which allows an IP-65 sealed connection when used with dielectric grease), and the other end can be plugged into a breakout board (or for ClearPath-SC, the SC communication hub), or cut off to create flying leads to allow you to wire into any control device you may use.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$23 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Controller Cable

Controller Cable, 55 ft
Part Number: CPM-CABLE-CTRL-MM660
Connectors: 8-pin Molex Mini-fit to 8-pin Molex Mini-fit
Length: 16.775 m (55 ft)

Cable to connect your digital control signals (from switches, buttons, PLCs, etc.) to your ClearPath motor. The 8-pin Molex connector connects to the motor. This cable can be cut to make two cables with a ClearPath connector on one end and flying leads on the other. Can also be used to connect an SC communication hub board to a ClearPath-SC motor, or an ASU-FR510 Analog Send Unit (analog to digital converter) to ClearPath motors and User I/O.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$112 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

 


USB Setup Cable

USB Cable

USB Cable, for Diagnostics, or SC4-HUB to PC
Part Number: CPM-CABLE-USB-120AB
Connectors: USB 2.0 A to B
Length: 3.05 m (10 ft)

Cable is used: 1) to use the diagnostic USB port on integral hp (AC input) ClearPath motors; or 2) to connect your host PC to a ClearPath-SC communication hub (e.g SC4-HUB). NOTE: This cable cannot be used with the diagnostic (rear USB) port of fractional hp (DC input) ClearPath models; for those, use the CPM-CABLE-USB-120 which has a micro-B connector.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$9 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

 


Logic Backup Power Cable

24 Volt Power, 2-Pin Molex Cable

24 Volt Power, 2-Pin Molex Cable
Part Number: CPM-CABLE-M2P2P-120
Connectors: 2-pin Molex to 2-pin Molex
Length: 10 ft

Cable used to supply 24 volt logic power to a number of ClearPath devices (e.g., Logic backup for AC-input motors, SC4-HUB power, daisy-chained power from SC4-HUB to SC4-HUB, ASU-FR510, power from POWER4-HUB to SC4-HUB, etc.) Can be cut in half to make two shorter cables with flying leads.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$13 $12 $11 $10 CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

 


Increase Output Power

Regenerated Energy Shunt

Regenerated Energy Shunt
Part Number: RES-225
Connector: Screw Terminal Block
Dimensions, in: 9.0 x 4.25 x 2.44
Weight: 1.6 lbs

The RES-225 is a regenerative energy dissipation unit that is compatible with AC input ClearPath motors. The RES-225 will monitor and manage your motor's regenerative energy output and provides up to 250W of continuous energy dissipation. For wiring and installation instructions, refer to the AC ClearPath Manual.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$152 REQUIRES QUICK REGISTRATION CONTACT

Until January 30, 2018, this accessory has a 4 week lead time (i.e., will ship 4 weeks after you order). After this date, quantities up to 5 will ship within 3 days, and quantities greater than 5 will ship within 3 weeks.

Blower Kit

Blower Kit
Part Number: BLOWER-1P230V
Connector: Screw Terminal Block
Length: Adds 2.12 in to motor length (see manual/3D models for specifics)
Input Power: Single-phase 190-253 VAC (min/max)
Weight: 2.0 lbs

This blower kit (AC powered fan and shroud) provides a significant increase in continuous torque for certain AC-input (integral hp) ClearPath motors. Motor part numbers shown with a “_fan” after them show the increased specifications using this blower. Note that this kit is not IP rated for dust or liquid protection, and needs AC wiring separate from the motor. For wiring and installation instructions, refer to the user manual: AC Input, Integral Horsepower ClearPath Motors.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$57 REQUIRES QUICK REGISTRATION CONTACT

Until January 30, 2018, this accessory has a 4 week lead time (i.e., will ship 4 weeks after you order). After this date, quantities up to 5 will ship within 3 days, and quantities greater than 5 will ship within 3 weeks.

 


Mounting Accessories

Foot Mount Kit

Foot Mount Kit
Part Number: FOOT-56-14X
Dimensions, in: 7.79 x 6.75 x 0.834
Weight: 1.4 lbs

The optional foot mounting plate is compatible with AC-input ClearPath motors, and is an alternative mounting method to face mounting. For mounting instructions, refer to the AC ClearPath Manual.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$14 REQUIRES QUICK REGISTRATION CONTACT

Until January 30, 2018, this accessory has a 4 week lead time (i.e., will ship 4 weeks after you order). After this date, quantities up to 5 will ship within 3 days, and quantities greater than 5 will ship within 3 weeks.

 


Software

ClearPath MSP

Motor Setup Program
Part Number: CPM-MSP
OS Compatibility: Windows 7, 8.1, 10

This software is used to customize your ClearPath-MC or -SD motor for your application. It also provides simple, but powerful diagnostic tools to help you measure how well your motor is performing and diagnose problems you may have with the motor or mechanics. You get an unlimited license to copy and use this software upon your first purchase of a ClearPath motor.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
REQUIRES QUICK REGISTRATION
Requires quick registration

Required Accessories

350/500 Watt DC Power Supply

350/500 Watt DC Power Supply
Part Number: IPC-5
Output: 75 VDC, 350 W cont. (500 W fan-cooled), 900 W peak
Input: 108-250 VAC
Connectors: 8-pin Molex Mini-fit (input) and 2-pin Sabre (output)
Dimensions, in (mm): 7.20 (183) x 5.20 (132) x 2.26 (57.3)
Weight, lbs (kg): 2.25 (1.02)
Certifications: UL recognized, CE pending

More ►

Low Voltage (75 VDC) "Intelligent Power Center" power supply optimized for motor drive bus power. Compatible with ClearPath NEMA 23 and 34 integrated servos, and Eclipse and Meridian 2xx-5xx series products.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$248 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

225 Watt DC Power Supply

225 Watt DC Power Supply
Part Number: IPC-3
Output: 75 VDC, 225 W cont., 900 W peak
Input: 108-250 VAC
Connectors: 8-pin Molex Mini-fit (input) and 2-pin Sabre (output)
Dimensions, in (mm): 7.13 (181) x 5.20 (132) x 2.26 (57.3)
Weight, lbs (kg): 2.11 (0.96)
Certifications: UL recognized, CE pending

More ►

Low Voltage (75 VDC) "Intelligent Power Center" power supply optimized for motor drive bus power. Compatible with ClearPath NEMA 23 and 34 integrated servos, and Eclipse and Meridian 2xx-5xx series products.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$199 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

AC Power Cable for IPC-3 and IPC-5

AC Power Cable for IPC-3 and IPC-5
Part Number: IPC35-CABLE110
Connectors: 8-pin Molex Mini-fit to U.S. standard 3-prong 120V AC plug (NEMA 5-15)
Length: 1.98 m (6.5 ft)

AC Power (120VAC) Cable for IPC-3 and IPC-5 motor drive power supplies.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$14 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

DC Power Cable

DC Power Cable
Part Number: CPM-CABLE-PWR-MS120
Connectors: 4-pin Molex Mini-fit to 2-pin Sabre
Length: 3.05 m (10 ft)

Cable used to supply bus power from a DC power supply to a ClearPath motor. The Molex end connects to the ClearPath motor; the Sabre end connects directly to a Teknic IPC-5 or IPC-3 power supply, but can be cut off if you intend to wire it to another supply.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$19 REQUIRES QUICK REGISTRATION CONTACT
DC Power Cable

DC Power Cable
Part Number: CPM-CABLE-PWR-MM660
Connectors: 4-pin Molex Mini-fit to 4-pin Molex Mini-fit
Length: 16.775 m (55 ft)

Cable used to supply bus power from a DC power supply to a ClearPath motor. It can be cut to make two cables or one long cable with flying leads at one end. (This is a 2-wire cable, so it is not suitable for use as the analog input cable on an ASU-FR510.)
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$85 $418 $391 $362 CONTACT
DC Power Distribution Hub

DC Power Distribution Hub
Part Number: POWER4-HUB
Input: Bus Power: 24-75 volts (nominal);
Logic Power: 15-30 volts
Output: Distributes the applied input voltages
Connectors: Bus: 2-pin Sabre; Logic: 2-pin Molex MiniFit Jr.
Dimensions, in (mm): 3.06 x 4.12 (77.7 x 104.7)
Certifications: UL, CE (pending)

Distributes DC bus power to up to four ClearPath motors. Requires 24 volt power to operate (in addition to bus power). The Power Hub also acts as logic power backup for the motors, i.e., the motors will still retain encoder position even with bus power removed (for safety during an E-stop, for example). Upon restoration of bus power, the motors will automatically return to their previous positions, if desired.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$49 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

DC Power Cable

DC Power Cable
Part Number: PC-SBR-72
Connectors:2-pin Sabre to 2-pin Sabre
Length: 1.89 meters (6 ft)

Cable used to supply 75 volt bus power from an IPC-5 or IPC-3 to a ClearPath-SC power distribution hub (e.g., POWER-4HUB) or to daisy-chain two power distribution hubs.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$18 $17 $15 $11 CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

24 Volt Power, 2-Pin Molex Cable

24 Volt Power, 2-Pin Molex Cable
Part Number: CPM-CABLE-M2P2P-120
Connectors: 2-pin Molex to 2-pin Molex
Length: 10 ft

Cable used to supply 24 volt logic power to a number of ClearPath devices (e.g., SC4-HUB power, daisy-chained power from SC4-HUB to SC4-HUB, ASU-FR510, power from POWER4-HUB to SC4-HUB, etc.) Can be cut in half to make two shorter cables with flying leads.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$13 $12 $11 $10 CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Controller Cable

Controller Cable
Part Number: CPM-CABLE-CTRL-MU120
Connectors: 8-pin Molex Mini-fit to 8-pin Molex Mini-fit (one connector is overmolded)
Length: 3.05 m (10 ft)

This cable connects your digital control signals (from switches, buttons, PLCs, etc.) to your ClearPath motor. The overmolded Molex connector connects to the motor (which allows an IP-65 sealed connection when used with dielectric grease), and the other end can be plugged into a breakout board (or for ClearPath-SC, the SC communication hub), or cut off to create flying leads to allow you to wire into any control device you may use.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$23 $22 $20 $19 CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Controller Cable

Controller Cable
Part Number: CPM-CABLE-CTRL-MM660
Connectors: 8-pin Molex Mini-fit to 8-pin Molex Mini-fit
Length: 16.775 m (55 ft)

Cable to connect your digital control signals (from switches, buttons, PLCs, etc.) to your ClearPath motor. The 8-pin Molex connector connects to the motor. This cable can be cut to make two cables with a ClearPath connector on one end and flying leads on the other. Can also be used to connect an SC communication hub board to a ClearPath-SC motor, or an ASU-FR510 Analog Send Unit (analog to digital converter) to ClearPath motors and User I/O.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$112 $105 $95 $89 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

USB Cable

USB Cable
Part Number: CPM-CABLE-USB-120
Connectors: USB 2.0 A to Micro-B
Length: 3.05 meters (10 ft)

Cable used to connect a ClearPath-MC or -SD motor to a Windows PC in order to configure the motor using the ClearPath MSP software. Once configured, the motor is disconnected from the PC, so you only need one of these cables no matter how many ClearPath motors you buy. This cable can also be used to connect to the rear diagnostic port of a ClearPath-SC motor.)
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$9 $9 $8 $7 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Analog Send Unit

Analog Send Unit
Part Number: ASU-FR510
Connectors: Molex Mini-fit (8, 4 and 2-pin)
Dimensions, in (mm): 4.63 (117.6) x 2.09 (53.1) x 1.45 (36.8)
DC Input Power: 15-30 VDC

PDF Icon User Manual

Need to use analog control signals? For maximum noise immunity, ClearPath-MC natively uses digital control signals, but this “Analog Send Unit” (ASU) allows you to use analog control signals (0-10V or 4-20mA) while minimizing associated noise issues. The ASU converts analog signals to digital signals compatible with ClearPath-MC, so you won’t have noise corruption. Just locate the ASU as close as possible to your analog source and send the accurately converted digital signals to ClearPath’s optically isolated inputs for high-fidelity control.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$59 $56 $52 $48 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

24 Volt Power, 2-Pin Molex Cable

24 Volt Power, 2-Pin Molex Cable
Part Number: CPM-CABLE-M2P2P-120
Connectors: 2-pin Molex to 2-pin Molex
Length: 10 ft

Cable used to supply 24 volt logic power to a number of ClearPath devices (e.g., SC4-HUB power, daisy-chained power from SC4-HUB to SC4-HUB, ASU-FR510, power from POWER4-HUB to SC4-HUB, etc.) Can be cut in half to make two shorter cables with flying leads.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$13 $12 $11 $10 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

ClearPath MSP

Motor Setup Program
Part Number: CPM-MSP
OS Requirements: Windows 7, 8, 8.1, Vista, XP

This software is used to customize your ClearPath-MC or -SD motor for your application. It also provides simple, but powerful diagnostic tools to help you measure how well your motor is performing and diagnose problems you may have with the motor or mechanics. You get an unlimited license to copy and use this software upon your first purchase of a ClearPath motor.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
Free Download
Download

Checklist of Required Components

350/500 Watt DC Power Supply

350/500 Watt DC Power Supply
Part Number: IPC-5
Output: 75 VDC, 350 W cont. (500 W fan-cooled), 900 W peak
Input: 108-250 VAC
Connectors: 8-pin Molex Mini-fit (input) and 2-pin Sabre (output)
Dimensions, in (mm): 7.20 (183) x 5.20 (132) x 2.26 (57.3)
Weight, lbs (kg): 2.25 (1.02)
Certifications: UL recognized, CE pending

More ►

Low Voltage (75 VDC) "Intelligent Power Center" power supply optimized for motor drive bus power. Compatible with ClearPath NEMA 23 and 34 integrated servos, and Eclipse and Meridian 2xx-5xx series products.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$248 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

225 Watt DC Power Supply

225 Watt DC Power Supply
Part Number: IPC-3
Output: 75 VDC, 225 W cont., 900 W peak
Input: 108-250 VAC
Connectors: 8-pin Molex Mini-fit (input) and 2-pin Sabre (output)
Dimensions, in (mm): 7.13 (181) x 5.20 (132) x 2.26 (57.3)
Weight, lbs (kg): 2.11 (0.96)
Certifications: UL recognized, CE pending

More ►

Low Voltage (75 VDC) "Intelligent Power Center" power supply optimized for motor drive bus power. Compatible with ClearPath NEMA 23 and 34 integrated servos, and Eclipse and Meridian 2xx-5xx series products.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$199 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

AC Power Cable for IPC-3 and IPC-5

AC Power Cable for IPC-3 and IPC-5
Part Number: IPC35-CABLE110
Connectors: 8-pin Molex Mini-fit to U.S. standard 3-prong 120V AC plug (NEMA 5-15)
Length: 1.98 m (6.5 ft)

AC Power (120VAC) Cable for IPC-3 and IPC-5 motor drive power supplies.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$14 $12 $11 $11 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

DC Power Cable

DC Power Cable
Part Number: CPM-CABLE-PWR-MS120
Connectors: 4-pin Molex Mini-fit to 2-pin Sabre
Length: 3.05 m (10 ft)

Cable used to supply bus power from a DC power supply to a ClearPath motor. The Molex end connects to the ClearPath motor; the Sabre end connects directly to a Teknic IPC-5 or IPC-3 power supply, but can be cut off if you intend to wire it to another supply.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$19 $18 $16 $15 Contact
DC Power Cable

DC Power Cable
Part Number: CPM-CABLE-PWR-MM660
Connectors: 4-pin Molex Mini-fit to 4-pin Molex Mini-fit
Length: 16.775 m (55 ft)

Cable used to supply bus power from a DC power supply to a ClearPath motor. It can be cut to make two cables or one long cable with flying leads at one end. (This is a 2-wire cable, so it is not suitable for use as the analog input cable on an ASU-FR510.)
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$85 $418 $391 $362 Contact
DC Power Distribution Hub

DC Power Distribution Hub
Part Number: POWER4-HUB
Input: Bus Power: 24-75 volts (nominal);
Logic Power: 15-30 volts
Output: Distributes the applied input voltages
Connectors: Bus: 2-pin Sabre; Logic: 2-pin Molex MiniFit Jr.
Dimensions, in (mm): 3.06 x 4.12 (77.7 x 104.7)
Certifications: UL, CE (pending)

Distributes DC bus power to up to four ClearPath motors. Requires 24 volt power to operate (in addition to bus power). The Power Hub also acts as logic power backup for the motors, i.e., the motors will still retain encoder position even with bus power removed (for safety during an E-stop, for example). Upon restoration of bus power, the motors will automatically return to their previous positions, if desired.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$49 REQUIRES QUICK REGISTRATION CONTACT

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

DC Power Cable

DC Power Cable
Part Number: PC-SBR-72
Connectors:2-pin Sabre to 2-pin Sabre
Length: 1.89 meters (6 ft)

Cable used to supply 75 volt bus power from an IPC-5 or IPC-3 to a ClearPath-SC power distribution hub (e.g., POWER-4HUB) or to daisy-chain two power distribution hubs.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$18 $17 $15 $11 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

24 Volt Power, 2-Pin Molex Cable

24 Volt Power, 2-Pin Molex Cable
Part Number: CPM-CABLE-M2P2P-120
Connectors: 2-pin Molex to 2-pin Molex
Length: 10 ft

Cable used to supply 24 volt logic power to a number of ClearPath devices (e.g., SC4-HUB power, daisy-chained power from SC4-HUB to SC4-HUB, ASU-FR510, power from POWER4-HUB to SC4-HUB, etc.) Can be cut in half to make two shorter cables with flying leads.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$13 $12 $11 $10 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Network Hub for ClearPath-SC Series

Network Hub for ClearPath-SC Series
Part Number: SC4-HUB
Input: 15-30 volts
Connectors: See drawing
Dimensions, in (mm): 3.56 x 5.31 (90.4 x 134.9)
Certifications: UL, CE (pending)

Required for ClearPath-SC systems. Provides network connection for up to four axes. Up to four SC hubs can be daisy-chained to create networks of up to 16 axes (per COM port). Automatic brake control outputs are provided (max of two per daisy-chain). One digital input is provided to E-stop all axes simultaneously.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$49 $46 $42 $39 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Controller Cable

Controller Cable
Part Number: CPM-CABLE-CTRL-MU120
Connectors: 8-pin Molex Mini-fit to 8-pin Molex Mini-fit (one connector is overmolded)
Length: 3.05 m (10 ft)

This cable connects your digital control signals (from switches, buttons, PLCs, etc.) to your ClearPath motor. The overmolded Molex connector connects to the motor (which allows an IP-65 sealed connection when used with dielectric grease), and the other end can be plugged into a breakout board (or for ClearPath-SC, the SC communication hub), or cut off to create flying leads to allow you to wire into any control device you may use.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$23 $22 $20 $19 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

Controller Cable

Controller Cable
Part Number: CPM-CABLE-CTRL-MM660
Connectors: 8-pin Molex Mini-fit to 8-pin Molex Mini-fit
Length: 16.775 m (55 ft)

Cable to connect your digital control signals (from switches, buttons, PLCs, etc.) to your ClearPath motor. The 8-pin Molex connector connects to the motor. This cable can be cut to make two cables with a ClearPath connector on one end and flying leads on the other. Can also be used to connect an SC communication hub board to a ClearPath-SC motor, or an ASU-FR510 Analog Send Unit (analog to digital converter) to ClearPath motors and User I/O.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$112 $105 $95 $89 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

USB Cable

USB Cable
Part Number: CPM-CABLE-USB-120AB
Connectors: USB 2.0 A to B
Length: 3.05 m (10 ft)

Cable used to connect your host PC to a ClearPath-SC communication hub (e.g., SC4-HUB). Note: this cable cannot be used with ClearPath-MC or -SD series models; for those, use CPM-CABLE-USB-120 (which has a micro-B connector).
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$9 $9 $8 $7 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

USB Cable

USB Cable
Part Number: CPM-CABLE-USB-120
Connectors: USB 2.0 A to Micro-B
Length: 3.05 meters (10 ft)

Cable used to connect a ClearPath-MC or -SD motor to a Windows PC in order to configure the motor using the ClearPath MSP software. Once configured, the motor is disconnected from the PC, so you only need one of these cables no matter how many ClearPath motors you buy. This cable can also be used to connect to the rear diagnostic port of a ClearPath-SC motor.)
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$9 $9 $8 $7 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

I/O Cable, 4-Pin Molex

I/O Cable, 4-Pin Molex
Part Number: CPM-CABLE-M4P4P-120
Connectors: 4-pin Molex Mini-fit to 4-pin Molex Mini-fit
Length: 10 ft

Cable used to connect an analog input to an ASU-FR510 Analog Send Unit (analog to digital converter).
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
$14 $13 $12 $11 Contact

Quantities up to 5 will ship within 3 business days. Quantities greater than 5 will ship within three weeks.

ClearPath ClearView

ClearPath-SC Series Setup Software
Part Number: CPM-CLEARVIEW
OS Requirements: Windows Vista, XP, 7, 8, 8.1, 10

This software is used to manually control and configure your ClearPath-SC motors. It also provides simple, but powerful diagnostic tools to help you measure how well your motors are performing and diagnose problems you may have with a motor or your mechanics. You get an unlimited license to copy and use this software upon your first purchase of a ClearPath-SC motor.
Qty 1-9 Qty 10-49 Qty 50-99 Qty 100-199 Qty 200+
Free Download
Download